2B-100 Perimeter DA600+ Alarm with Receiver & 2 x Power Packs

Long Range 2B Solar Powered Wireless DA600+ Perimeter Alarm System supplied with a set of 2B Wireless Beams, 1 x 4-channel Wireless Receiver & 2 x Power Packs.

Compatible with all DA600+ products !!

The operational range between the Receiver & Beams is 900 metre (line of sight) & the detection range is 100 metre, ideal to help you protect your Family, Home & Business, designed for simple DIY Installation.

Rechargeable Power Packs:

These Power Packs are designed for helping to power and maintain the Solar Beams in either:

• Very busy locations (hundreds of activations per day).
• Dark locations such as:
  • Under a large Tree.
  • Behind a large North Facing Wall.
  • Inside the Entrance to an Open Barn.
  • Inside a fully enclosed Building.

The Power Pack will operate the Beams for approximately 750 activations before needing to be recharged, the Beams will also still have their built in Batteries and Solar Panels.

When the Power Pack needs charging, you simply unclip and remove it from the weatherproof container (no tools required) and take it to the charger (3-pin charger supplied), whilst the Power Pack is being charged the Beams will operate normally being powered by the Internal Batteries.

For locations inside buildings near to a power supply, you could even keep the Power Pack permanently connected to the Charger.

Receiver:

The Indoor 4 - Channel Wireless Receiver is powered by a standard 3-pin Plug in Transformer and has the following features:

• 4 x Adjustable Dry Relay N/O or N/C Outputs (often used to trigger auto-diallers, timer relays).
• Adjustable 12v DC Outputs (often used with sirens & flashing lights).
• ON/OFF Switch.
• Volume Control.
• Will work with up to 128 sets of Detectors.
• Optional Reminder Bleeps.
• Exit Delay Option.

Receiver:

• 1 x 4-Channel Indoor Receiver.
• 1 x Plug in Transformer. 
• 1 x Rear Mouning Bracket.
• 1 x Manual. 

Detection Beams:

• 1 x Set of 2B Solar Powered Detecting Beams.
• 1 x Set of Wall Mounting Brackets. 
• 1 x Set of Pole Mounting Brackets.
• 1 x Set of Instructions. 

Rechargeable Power Pack:

• 2 x Rechargeable Power Packs.
• 2 x 3-pin Plug in Chargers.
• 2 x IP67 Plastic Boxes.
• 2 x Snap Cable Connectors.

Receiver:

• Receiver Size: 160 (W) x 105 (H) x 35 (D) mm.
• Power Supply: 15v DC 1amp (plug in transformer).
• ON/OFF Button: Yes.
• Adjustable Volume Control: Yes.
• Available Channels: 4.
• Max sets of Beams per Channel: 32.
• Maximum sets of Detectors per Receiver: 128.
• Output Voltage: 12v DC.
• Output Voltage Duration: 1, 10, 60 second & 5 minutes.
• Built in Chimes: Yes (one per channel).
• Reminder Bleep: Yes (if programmed).
• Exit Delay: Yes 5 minutes (if programmed).
• Frequency: 434.6 MHz.
• Standby Current: 20 mA.
• Alarm Current: 180 mA.
• Relay Rating: 24v DC or 120v AC (2 amp).
• Relay Output Type: Momentary N/O or N/C.
• Wireless Working Range: 900 metres (line of sight).

Detection Beams:

• Beam Size: 590 (H) x 123 (W) x 45 (D) mm.
• Power Supply: Re-chargeable AA Batteries.
• Charging Method: Built in Solar Panels.
• Mounting Methods: Wall or Pole.
• Detection Range: 100 metres.
• Transmission Range: 900 metres (line of sight).
• Frequency: 433 Mhz.
• IP Rating: IP66.
• Distance Between Detection Beams: 60mm.
• Quantity of Built in Detection Beams: 2 sets.
• Charging Port: 9 - 12v DC (500 m/A to 1 amp).
• Built in Buzzer: Yes (turn on with 1 - 6 presses of button, off 7 or 8 times).
• Buzzer OFF (7 with immediate reset, 8 with 3 minutes battery saving reset).

Easy Programming Method:

1. Turn On Beams (switch on rear).
2. Mount the Beams.
3. Line up By Eye, String Line etc.
4. Put the relevant Receiver into Learn Mode.
5. Walk through the Beams, at this time (providing you have them correctly lined up), a low red glow will illuminate briefly.
6. The Signal sent to the Receiver from this set of beams will be learned into the relevant receiver.
7. Take the Receiver out of learn mode.
8. The system is now ready.

Power Pack:

• Connection to Beams: 90 degrees Push Connector.
• Cable Length to Push Connector: 1.2 metre (could be lengthened upon request).
• Charging Method: Remove from IP67 Box (simple connector inside box), and take away to Charge with Charger supplied.
• Charging Time: Approx 6 - 8 Hours.
• Beam Operation: Approximately 750 Triggers before Charging required.

Storage Box:

• Material: Plastic.
• 200 x 170 x 100 mm.
• Weatherproof: Yes (IP67).
• Lid: Hinged with Snap Connector.