Compehensive 2B-100 Solar Wireless Perimeter Alarm, H/D GSM Auto-Dialler & Power Packs

Long Range Solar Powered Comprehensive 2B Wireless Perimeter GSM Alarm System with 900 metre Transmission & 100 metre Detection, supplied with:

• 4 x sets of Long Range 2B Solar Powered Wireless Perimeter Beams.
• 1 x 4 x channel Wireless Receiver.
• 1 x Heavy Duty KP GSM Auto-Dialler.
• 8 x Rechargeable Power Packs (designed to be used on Beams located in dark locations).

A complete Alarm System to help you Monitor & Secure your Perimeter, ideal for DIY Installation.

Rechargeable Power Packs:

These Power Packs are designed for helping to power and maintain the Solar Beams in either:

• Very busy locations (hundreds of activations per day).
• Dark locations such as:
  • Under a large Tree.
  • Behind a large North Facing Wall.
  • Inside the Entrance to an Open Barn.
  • Inside a fully enclosed Building.

The Power Packs will operate the Beams for approximately 750 activations before needing to be recharged, the Beams will also still have their built in Batteries and Solar Panels.

When the Power Pack needs charging, you simply unclip and remove it from the weatherproof container (no tools required) and take it to the charger (3-pin charger supplied), whilst the Power Pack is being charged the Beams will operate normally being powered by the Internal Batteries.

For locations inside buildings near to a power supply, you could even keep the Power Pack permanently connected to the Charger.

Receiver:

The Indoor 4 - Channel Wireless Receiver is powered by a standard 3-pin Plug in Transformer and has the following features:

• 4 x Adjustable Dry Relay N/O or N/C Outputs (often used to trigger auto-diallers, timer relays).
• Adjustable 12v DC Outputs (often used with sirens & flashing lights).
• ON/OFF Switch.
• 5 minute Exit Delay (using the remote controls or receiver).
• Volume Control.
• Will work with up to 128 sets of Detectors.
• Optional Reminder Bleeps.
• Exit Delay Option.

GSM Auto-Dialler:

The KP Heavy Duty GSM Auto-Dialler is constructed with a steel case, ideal for many commercial applications or the harsher environments.

It is connected to the Wireless Receiver by a short length of bell cable (supplied) and communicates through mobile phone networks, a standard sized SIM Card needs to be fitted (you can use either PAYG or Contract).

It is very easy to program by using the built in keypad, and easy to use with the following features:

• Will send up to 3 text messages when triggered.
• Up to 5 telephone numbers can be programmed (a maximum of 32 digits).
• Will contact main key-holder in the event of a 30 minute power failure (optional).
• Remote  operation (by text message).
• 4 methods of arming & disarming:
  • Keypad.
  • Remote Control.
  • Auto-setting.
  • Text Message.
• Adjustable entry & exit delay.
• Back up battery.
• 16 wired zones.
• 16 wireless zones (allows you to fit Intruder & Safety Sensors including wireless door contacts, internal PIR's, smoke & water sensors).
• 12v output (for connecting to sirens etc).
• Communication Method: Sim Card.
• External Aerial can be Fitted (for a better mobile phone signal).

The secret to using a GSM Auto-Dialler with a Perimeter Alarm is to use the Dialler as the central hub of the system, therefore any additional Sirens, Flashing Lights or Relays would be connected to the output of the Dialler (not the internal receiver), this gives you full control, even from remote locations via your mobile.

The Receiver is used for just two reasons, first to receiver the signal from all of the Detectors, the second as a useful Chime unit for when you are at home and you do not need the system Armed.

You can add many additional accessories to this Perimeter Alarm system to suit your application including:

• Additional Perimeter Beams (4 x sizes).
• Window Beams (2 x sizes).
• PIR's & Door Contacts.
• Smoke Detectors.
• External Wired & Wireless Sirens.
• Internal Sirens & Buzzers.
• Speech Alerts.
• Relays (for lighting).
• Flashing Lights.

*You can use up to 128 sets of Wireless Detectors with this single Alarm System*

If you require advice when building your system, please contact us for Friendly, No Obligation Advice !!

• 4 x Sets of Wireless 2B Solar Powered Perimeter Beams.
• 1 x Receiver & Plug in 3-pin Transformer (2-pin available upon request).
• 1 x Set of Brackets & Screws (for mounting the beams).
• 1 x KP Heavy Duty GSM Auto-Dialler, 2 x Remote Controls & Plug in 3-pin Transformer (2-pin available upon request).
• 8 x Rechargeable Power Packs & Chargers.
• 1 x Set of Manuals.

Wireless Receiver Specification:

• Size: 160 (W) x 105 (H) x 35 (D) mm.
• Power Input: 12 - 15v DC 1 amp.
• Power Supply: 3-pin Plug in Transformer (2-pin available upon request).
• ON/OFF Button: Yes.
• Adjustable Volume Control: Yes.
• Channels: 4.
• Max sets of Beams per Channel: 32.
• Output Voltage: 12 - 12v DC.
• Output Voltage Duration: 2 seconds to 10 minutes.
• Built in Chimes: Yes (one per channel).
• Reminder Bleep: Yes (if programmed).
• Exit Delay: Yes 5 minutes (if programmed).
• Frequency: 434.6 MHz.
• Standby Current: 20 mA.
• Alarm Current: 180 mA.
• Relay Rating: 24v DC or 120v AC (2 amp).
• Relay Output Type: Momentary N/O or N/C.

GSM Dialler Specification:

• Case Construction: Steel.
• 2 x Aerials: (detachable and extendable).
• Text Message: (will send up to 3 text messages when triggered, one text message following a power failure).
• Telephone Calls: (will call up to 5 telephone numbers).
• 16 x Wireless Zones (fully adjustable).
• 16 x Wired Zones (fully adjustable).
• Adjustable Power Failure Time Duration: (instantly or 30 minutes).
• 12v DC Input: (suitable for solar & battery applications).
• Can be Armed & Disarmed by: Built in Keypad, Remote Control, Self Auto-Timer & Text Message.
• Self Monitoring Mode: (optional use).
• 4 Minute Output Relay: (relay when the alarm is triggered, can operate sirens, lights, telephone dialers).
• 12v DC Output: (when triggered).
• Large selection of Alarm Accessories Available.
• Switch 4 Minute Relay: (can be used for the key-holder to switch on lights etc).
• Lockable Control Panel.
• Tamper Switch.
• Sirens: (can activate external wired & wireless sirens).
• Size: 225 (w) x 160 (h) x 50 (d) mm.
• Frequency: 433 Mhz.
• Quad Band: 850/900/1800/1900 MHz.

Beam Specification:

• Beam Size: 590 (H) x 123 (W) x 45 (D) mm.
• Power Supply: Re-chargeable AA Batteries.
• Charging Method: Built in Solar Panels.
• Mounting Methods: Wall or Pole.
• Detection Range: 100 metres.
• Transmission Range: 900 metres (line of sight).
• Frequency: 433 Mhz.
• IP Rating: IP66.
• Distance Between Detection Beams: 60mm.
• Number of Beams: 2 sets.
• Charging Port: 9 - 12v DC (500 m/A to 1 amp).
• Built in Buzzer: Yes (turn on with 1 - 6 presses of button, off 7 or 8 times).
• Buzzer OFF (7 with immediate reset, 8 with 3 minutes battery saving reset).

Easy Programming Method:

1. Turn On Beams (switch on rear).
2. Mount the Beams.
3. Line up By Eye, String Line etc.
4. Put the relevant Receiver into Learn Mode.
5. Walk through the Beams, at this time (providing you have them correctly lined up), a low red glow will illuminate briefly.
6. The Signal sent to the Receiver from this set of beams will be learned into the relevant receiver.
7. Take the Receiver out of learn mode.
8. The system is now ready.

GSM Auto-Dialler Programming:

• Best carried out after the Beams are programmed to the Receiver (see above).
• Connect Receiver to Dialler using Bell Cable (often done by us before despatch).
• Insert SIM Card.
• Connect and plug in the Power Supply.
• Turn ON (switch inside).
• Use Keypad to carry out the relevant programming.

Power Pack:

• Connection to Beams: 90 degrees Push Connector.
• Cable Length to Push Connector: 1.2 metre (could be lengthened upon request).
• Charging Method: Remove from IP67 Box (simple connector inside box), and take away to Charge with Charger supplied.
• Charging Time: Approx 6 - 8 Hours.
• Beam Operation: Approximately 750 Triggers before Charging required.

Power Pack Storage Box:

• Material: Plastic.
• 200 x 170 x 100 mm.
• Weatherproof: Yes (IP67).
• Lid: Hinged with Snap Connector.