Comprehensive 1B-100 Wireless Perimeter Alarm with H/D GSM Auto-Dialler

Long Range Solar Powered Comprehensive Wireless Perimeter GSM Alarm System with 900 metre Transmission & 100 metre Detection, supplied with:

• 4 x sets of Long Range 1B Solar Powered Wireless Perimeter Beams.
• 1 x 4 x channel Wireless Receiver.
• 1 x KP Heavy Duty GSM Auto-Dialler (ideal for commercial applications).

A complete Alarm System to help you Monitor & Secure your Perimeter, ideal for DIY Installation.

Receiver:

The Indoor 4 - Channel Wireless Receiver is powered by a standard 3-pin Plug in Transformer and has the following features:

• 4 x Adjustable Dry Relay N/O or N/C Outputs (often used to trigger auto-diallers, timer relays).
• Adjustable 12v DC Outputs (often used with sirens & flashing lights).
• ON/OFF Switch.
• Volume Control.
• 5 minute Exit Delay Possible: (using remote control or receiver).
• Will work with up to 128 sets of Detectors.
• Optional Reminder Bleeps.
• Exit Delay Option.

H/D GSM Auto-Dialler:

The KP Heavy Duty GSM Auto-Dialler is constructed with a steel case, ideal for many commercial applications or the harsher environments.

It is connected to the Wireless Receiver by a short length of bell cable (supplied) and communicates to key-holders through mobile phone networks, a standard sized SIM Card needs to be fitted (not supplied as standard but available in the drop down above), you can use either PAYG or Contract.

It is very easy to program by using the built in keypad, and easy to use with the following features:

• Will send up to 3 text messages when triggered.
• Up to 5 telephone numbers can be programmed (a maximum of 32 digits).
• Will contact main key-holder in the event of a 30 minute power failure (optional).
• Remote  operation (by text message).
• 4 methods of arming & disarming:
  • Keypad.
  • Remote Control.
  • Auto-setting.
  • Text Message.
• Adjustable entry & exit delay.
• Back up battery.
• 16 wired zones.
• 16 wireless zones (allows you to fit Intruder & Safety Sensors including wireless door contacts, internal PIR's, smoke & water sensors).
• 12v output (for connecting to sirens etc).
• Communication Method: Sim Card.
• External Aerial can be Fitted (for a better mobile phone signal).

The secret to using a GSM Auto-Dialler with a Perimeter Alarm is to use the Dialler as the central hub of the system, therefore any additional Sirens, Flashing Lights or Relays connected would only be active during suitable times.

The Auto-Dialler can be operated by:

• Built in Keypad.
• Built in Automatic Timer.
• Remote Controls.
• Text Message.

The Receiver is used for just two reasons, first to receiver the signal from all of the Detectors which informs the Auto-Dialler, the second as a useful Chime unit for when you are at home and you do not need the system Armed.

You can add many additional accessories to this Perimeter Alarm system to suit your application including:

• 3 sizes of additional Wireless Perimeter Beams (up to 128 can be used on any single system).
• 2 sizes of Window Beams.
• PIR's & Door Contacts.
• Smoke Detectors.
• External Wired & Wireless Sirens.
• Internal Sirens & Buzzers.
• Speech Alerts.
• Relays (for lighting).
• Flashing Lights.

If you require advice when building your system, please contact us for Friendly, No Obligation Advice !!

• 4 x Sets of Wireless Solar Powered Perimeter Beams.
• 1 x Receiver & Plug in 3-pin Transformer (2-pin available upon request).
• 1 x Set of Brackets & Screws (for mounting the beams).
• 1 x KP Heavy Duty GSM Auto-Dialler, 2 x Remote Controls & Plug in 3-pin Transformer.
• 1 x Set of Manuals.

Wireless Receiver Specification:

• Size: 160 (W) x 105 (H) x 35 (D) mm.
• Power Input: 12 - 15v DC 1 amp.
• Power Supply: 3-pin Plug in Transformer (2-pin available upon request).
• ON/OFF Button: Yes.
• Adjustable Volume Control: Yes.
• Channels: 4.
• Max sets of Beams per Channel: 32.
• Output Voltage: 12 - 12v DC.
• Output Voltage Duration: 2 seconds to 10 minutes.
• Built in Chimes: Yes (one per channel).
• Reminder Bleep: Yes (if programmed).
• Exit Delay: Yes 5 minutes (if programmed).
• Frequency: 434.6 MHz.
• Standby Current: 20 mA.
• Alarm Current: 180 mA.
• Relay Rating: 24v DC or 120v AC (2 amp).
• Relay Output Type: Momentary N/O or N/C.

GSM Dialler Specification:

• Case Construction: Steel.
• 2 x Aerials: (detachable and extendable).
• Text Message: (will send up to 3 text messages when triggered, one text message following a power failure).
• Telephone Calls: (will call up to 5 telephone numbers).
• 16 x Wireless Zones (fully adjustable).
• 16 x Wired Zones (fully adjustable).
• Adjustable Power Failure Time Duration: (instantly or 30 minutes).
• 12v DC Input: (suitable for solar & battery applications).
• Can be Armed & Disarmed by: Built in Keypad, Remote Control, Self Auto-Timer & Text Message.
• Self Monitoring Mode: (optional use).
• 4 Minute Output Relay: (relay when the alarm is triggered, can operate sirens, lights, telephone dialers).
• 12v DC Output: (when triggered).
• Large selection of Alarm Accessories Available.
• Switch 4 Minute Relay: (can be used for the key-holder to switch on lights etc).
• Lockable Control Panel.
• Tamper Switch.
• Sirens: (can activate external wired & wireless sirens).
• Size: 225 (w) x 160 (h) x 50 (d) mm.
• Frequency: 433 Mhz.
• Quad Band: 850/900/1800/1900 MHz.

Beam Specification:

• Size: 340 (H) x 123 (W) x 45 (D) mm.
• Power Supply: Re-chargeable AA Batteries.
• Mounting Methods: Wall or Pole.
• Detection Range: 100 metres.
• Transmission Range: 900 metres (line of sight).
• Frequency: 433 Mhz.
• IP Rating: IP66.
• Distance Between Detection Beams: 60mm.
• Qty of Detecting Beams: 1 set.
• Protected Height: 
• Charging Port: 9 - 12v DC (500 m/A to 1 amp).

Easy Beam Programming Method:

1. Turn On Beams (switch on rear).
2. Mount the Beams.
3. Line up By Eye, String Line etc.
4. Put the relevant Receiver into Learn Mode.
5. Walk through the Beams, at this time (providing you have them correctly lined up), a low red glow will illuminate briefly.
6. The Signal sent to the Receiver from this set of beams will be learned into the relevant receiver.
7. Take the Receiver out of learn mode.
8. The system is now ready.

GSM Auto-Dialler Programming:

• Best carried out after the Beams are programmed to the Receiver (see above).
• Connect Receiver to Dialler using Bell Cable (often done by us before despatch).
• Insert SIM Card.
• Connect and plug in the Power Supply.
• Turn ON (switch inside).
• Use Keypad to carry out the relevant programming.