Siren & Beams (fully solar powered) Wireless DA600+ Perimeter Alarm System

This unique Long Range Wireless DA600+ Perimeter Alarm consists of a set of Wireless Perimeter Beams & Wireless Solar Siren, no power is required on site, ideal for Remote locations.

Solar Siren:

The quality Solar Powered Siren & Bright Flashing LED Strobe Lights communicates directly with the 1B-100 Wireless Beams (supplied) together with any further Beams or Sensors you wish to add.

The Siren doubles up as the control panel and is Armed & Disarmed using a Remote Control from up to 100 metres away, the Siren can be programmed to operate in two ways:

• Alarm (in this mode once the Siren is Armed it will trigger a 100 Decibel Siren together with very bright Flashing LED Strobe Lights should any Detectors being activated).
• Alert (this mode will omit a 6 second Siren & Flashing Strobe, designed to be a visitor Alert for businesses where staff are working outside in a yard etc).

It is fitted onto a wall using a simple mounting bracket, it would be best to be fitted on a South facing wall if possible.

Beams:

The impressive 1B Solar Powered Wireless Beams (often called laser beams) are packed with impressive featured below:

• Battery Powered with Built in Solar Charging: (making for easy installation).
• Dual Detection Technology: (prevents false alarms from small animals and moving debris).
• 100 metre Detection: (covers more are with less detectors).
• Impressive 900 metre Wireless Range: 
• Quality Build.
• Supplied with Wall & Pole Mounting Brackets.
• Test Lights: (for easy installation).
• Top up charging Ports.
• Option Test Beep (which can be silenced).

The Dual Detection Technology works by having a pair of Detectors (set 60 mm apart from each other) on each Beam, both Detectors have to be breached simultaneously to create an activation, allowing small animals, insects, leaves & debris to safely pass by. There are a pair of detectors on each size of Beam, so these 1B-100 have one pair of detectors, a 2B-100 would have two pairs.    

The External Beams are also supplied with an additional Charging Port which can be used to give the Beams a boost charge should you experience a lengthy duration of low sun light, or perhaps one of the beams needs to be fitted into a slightly covered location. 

They are very easy to install as they have a built in Red Glow Light (for easy lining up).

Operating Range:

The Wireless operating range between the Beams & Siren is 900 metres (line of sight) which can be doubled by using the signal repeater (part number 004-2910), the Detection range is up to 100 metres.

You can use up to 32 sets with the Solar Wireless Siren, you can mix & match by using a selection of different sizes of Beams or Sensors within this single system.

You can also add the one or more Internal Receivers (part number 004-2880) should you need notification inside the House or Office.

Please Note: Compatible with all DA600+ products !!

Siren:

• 1 x Solar Powered Siren & Flashing Strobe Light.
• 1 x Wall Bracket.
• 2 x Remote Controls. 

Detector Beams:

• 1 x Set of Solar Powered Detecting Beams.
• 1 x Set of Wall Mounting Brackets. 
• 1 x Set of Pole Mounting Brackets.
• 1 x Set of Instructions.  

Siren:

• Size: 280 x 180 x 74 mm.
• Siren Options:
• • Loud 4 second chime.
  • Full Siren & Flashing Strobe (duration 1 minute).
• Siren Level: 90 decibel Chime mode, 110 decibel Siren mode.
• LED Illumination: 70 lm.
• Wireless Working Range to Remote Control: over 100 metres (line of sight).
• Wireless Working Range to Perimeter Beams: 900 metres (line of sight).
• Mounting Method: Rear Plate.
• Built in Battery: 3000mAH 6.4v.
• Battery Type: Lithium.
• Frequency: 433 MHz.
• Working Temperature: -30 - +70.

Beams:

• Beam Size: 340 (H) x 123 (W) x 45 (D) mm.
• Power Supply: Re-chargeable AA Batteries.
• Charging Method: Built in Solar Panels.
• Mounting Methods: Wall or Pole.
• Detection Range: 100 metres.
• Transmission Range: 900 metres (line of sight).
• Frequency: 433 Mhz.
• IP Rating: IP66.
• Distance Between Detection Beams: 60mm.
• Number of Beams: 1 set.
• Charging Port: 9 - 12v DC (500 m/A to 1 amp).

Easy Programming Method:

1. Turn On Beams (switch on rear).
2. Mount the Beams.
3. Line up By Eye, String Line etc.
4. Put the relevant Receiver into Learn Mode.
5. Walk through the Beams, at this time (providing you have them correctly lined up), a low red glow will illuminate briefly.
6. The Signal sent to the Receiver from this set of beams will be learned into the relevant receiver.
7. Take the Receiver out of learn mode.
8. The system is now ready.